Cemflow RENOVATION MESH
Previous product
Next product
Cemflow RENOVATION
 

Cemflow
COMMERCIAL

FAST TRACK COMMERCIAL UNDERLAYMENT
 
Description:

Cemflow Renovation is designed as a medium duty floor topping for upgrading and renovating new and existing commercial and industrial internal floors.

Usage

Cemflow Commercial is supplied as a pre-blended dry powder and can be applied between 0.5mm to 10mm (in one application) to provide an underlayment or wearing floor.

Cemflow Commercial is self-smoothing, dimensionally stable and fast drying. Cemflow Commercial is suitable for application on to a wide range of subfloor types, including; sand and cement screeds, concrete, terazzo, granolithic, epoxy and polyurethane resins and waterproof membranes.

When used as a wearing floor, Cemflow Commercial should be sealed using Cemflow Sealer following the instructions on the sealer technical datasheet. When used as an underlayment Cemflow Commercial can receive floor coverings after 24 hours.

Cemflow Commercial is protein free so may be used in biologically sensitive areas.

Materials Supplied

25 kg paper sacks. 

Coverage

A 25kg bag using 5 litres of clean water will yield approx. 14.4 litres.

A 25kg pack of Cemflow Commerical will cover approximately 4.8 m² at 3mm thickness.

Storage

Protect from frost and store under dry warehouse conditions at a temperature between 10 °C and 30 °C.

Shelf Life

6 months in unopened bags and stored under good conditions.

Technical Information

EN 13813 ClassCT-C25-F6-AR1
Working time @ 20°C15 – 20 minutes
Setting time @ 20°C90 minutes
Foot traffic
3 hours
Compressive Strength (N/mm²)
EN 13892-2 
1 day
7 days
28 days


> 6.0
> 15.0
> 30.0
Flexural Strength (N/mm²)
EN 13892-2 
1 day
7 days
28 days


> 2.0
> 4.0
> 5.0
Consumption per mm thickness
1.75 kg/m²
Application thickness0.5 - 10 mm
Slip resistance
EN 13036-4
Dry 69
Wet 54
Abrasion resistance
EN 13892-4
AR1
BRE Screed test1.00 mm

Application Instructions

SURFACE PREPARATION

Concrete and sand/cement screeds must be sound, dry and fully cured (not subject to shrinkage) and any laitance or surface treatments must be removed by mechanical means such as grit blasting. The surface tensile strength of the substrate should be a minimum 1.5 N/mm². If applying over Cemflow Base an STR should be used to remove any laitance followed by vacuuming and priming with Neoprene Primer.

The concrete substrate should be below 75% RH alternatively Strongcoat DPM should be applied. The temperature of the floor must be maintained above 10°C throughout the application and drying of the Cemflow COMMERCIAL.

PRIMING

TO CONCRETE AND CEMENT SCREEDS
For application on to sand / cement screeds, concrete and other porous substrates, first seal the prepared surface by applying one diluted coat of Neoprene PRIMER, diluted one part Neoprene PRIMER with 4 parts potable water by soft broom or brush, and allow to thouroughly dry. Apply a second coat of primer diluted 3:1 by the same method and allow thoroughly to dry. Depending on the porosity of the substrate a further coat may be required. To confirm if this is necessary a small application area should be undertaken to ascertain the correct priming requirements. As an alternative, Strongcoat PRIMER may be used.

PRIMING WITH STRONGCOAT PRIMER
Apply one coat Strongcoat PRIMER and allow to cure. Apply 2nd coat and whilst still tacky fully blind with DCP Coarse Aggregate at approximately 3 kg/m² until the surface is covered and no resin spots remain. The rate of application is approximately 3 kg/m². Allow to dry fully overnight and remove excess aggregate before applying the Cemflow COMMERCIAL.

TO CURED CEMFLOW BASE/RENOVATION
For curing Cemflow Base/Renovation apply Neoprene Primer diluted 3 parts water t o 1 part Neoprene Primer by brush or soft broom and allow to dry thoroughly. Apply a further application o f Neoprene Primer dilute d 3:1 with water and again allow to dry thoroughly.

TO IMPERVIOUS SURFACES
For application on to impervious surfaces, such as tiles, coatings or onto Strongcoat DPM (please read relevant product technical data sheet). Apply Strongcoat PRIMER and whilst it is still tacky fully blind with DCP Coarse Aggregate at approximately 3 kg/m², until the surface is covered and no resin spots remain. Allow to dry fully overnight and remove excess aggregate before applying the Cemflow COMMERCIAL.

MIXING 

Us e a power-whisk fitted in a heavy-duty slow speed electric drill. Mix in the proportion of 25kg of powder to 5.0 litres of potable water. Pour the water into a suitably sized bucket and gradually add the powder while stirring, until a smooth, lump free consistency is achieved. Mix for a minimum of 2 minutes.

APPLICATION

HAND APPLICATION
Pour the mixed material onto the prepared surface and allow to attain a smooth finish. The use of a spiked roller will help to eliminate entrapped air and smooth out flow lines. Apply at a thickness between 0.5 - 10mm in one application. The product will remain workable for approximately 15-20 minutes at 20°C. Cemflow Commercial will accept foot traffic after approximately 3 hours and light traffic after approximately 24 hours at 20°C.

PUMP APPLICATION
Cemflow Commercial is suitable for pump application up to 10mm thickness. Please contact our Technical Department for more specific information.

For the application of any seal coats, please refer to relevant Technical Data Sheets.

CLEANING
Wash tools with water immediately after use.

PRECAUTIONS
Do not place when the substrate temperature is below 10 °C or when the ambient temperature is 10 °C and falling. Protect from frost. Do not exceed the maximum recommended water content and only use potable cold water.

This product is not recommended for external use or situations where water may come into direct contact with the cured material.

This product should not be applied to ashpalt or bituminous surfaces.

HEALTH AND SAFETY
Refer to the product Material Safety Data Sheets before using Cemflow COMMERCIAL.



Download file




Connect with Don Construction Products


  Complaints Record Form

  Customer Satisfaction

Name *
Email *
Phone
Address
Subject
Request  
Security Code *

Don Construction Products Ltd.

Headquarters
Hawthorn House, Helions Bumpstead Road,
Haverhill, Suffolk, CB9 7AA, United Kingdom
Tel: +44 (0) 1440 766360 
Fax: +44 (0) 1440 768897

Email: sara.harvey@dcp-int.co.uk
Email: stephen.bird@dcp-int.co.uk
Email: tom.emery@dcp-int.com