Strongcoat TOPPING
Previous product
Next product
Strongcoat HB
 

STRONGCOAT
EPOXY OT

Two-part oil tolerant epoxy DPM and primer
 
Description:

Strongcoat Epoxy OT is a two-component epoxy resin primer and membrane designed to be used on concrete floors where oil contamination is present

Usage

Strongcoat Epoxy OT is designed to improve adhesion of surface coatings and screeds to substrates which are contaminated with oils. Note that whilst Strongcoat Epoxy OT is oil tolerant, it will not adhere to grossly contaminated substrates. Substrates should be thoroughly cleaned with industrial detergent before applying Strongcoat Epoxy OT.

Materials Supplied

5 kg and 10 kg units.

Coverage

On grit blasted and textured surfaces, approximately 3.5 m²/kg for the first coat and up to 5 m²/kg for the second coat. Coverage figures will vary according to the texture, porosity and evenness of the surface on which the Strongcoat Epoxy OT is being applied.

Storage

Protect from frost and store under dry warehouse conditions at a temperature between 5°C and 30°C.

Shelf Life

12 months if stored in unopened packaging and stored under proper conditions.

Technical Information

Bond strength
BS EN 13892-8:2002
1.5 MPa
Working time @ 20°C15 - 20 min
Overcoat time12 - 36 hr

APPLICATION INSTRUCTIONS

SURFACE PREPARATION

Concrete substrates should be mechanically prepared to remove any dust, laitance, grease, oil or any other contaminants that could adversely affect adhesion.

Suitable mechanical preparation such as scrabbling, planning or vacuum grit blasting are recommended to provide a key. A suitable degreaser and cleaning agent should be applied to any residual oil contamination.
Thoroughly rinse with clean water following cleaning to remove any residue. Ensure no standing water is present before application.

MIXING

Taking care to ensure that the bottom and sides are thoroughly scraped, transfer the entire contents of the Strongcoat Epoxy OT Hardener container into the Resin container and, using a Jiffytype mixer attached to a slow-running electric drill, mix for approximately two minutes.

Never mix Strongcoat Epoxy OT by hand as this could lead to areas of uncured material.

APPLICATION

Once mixing is complete, transfer the Strongcoat Epoxy OT to a roller tray and, using a medium-pile simulated sheepskin roller, apply it evenly over the surface. The second coat or further toppings must be applied within 48 hours. If used as a primer for cementitious floor coatings the second coat should receive a full blind of DCP coarse aggregate at a rate of approximately 3 kg/m². Any excess aggregate should be removed once the primer has cured.

WORKING TIME
Strongcoat Epoxy OT has a working time of approximately 20 minutes at 20°C.

Never leave the mixed Strongcoat Epoxy OT kit to stand for any length of time prior to application as this will considerably shorten its working time.

PRECAUTIONS

Do not place when the substrate temperature is below 10°C or when the ambient temperature is 10°C and falling. Do not place where the atmospheric relative humidity is above 90%. Substrates should be kept 3°C above the dew point for at least 48 hours after application.
Protect from frost.

HEALTH & SAFETY

Refer to the product Material Safety Data Sheets before using Stroncoat Epoxy OT.



Download file




Connect with Don Construction Products


  Complaints Record Form

  Customer Satisfaction

Name *
Email *
Phone
Address
Subject
Request  
Security Code *

Don Construction Products Ltd.

Headquarters
Hawthorn House, Helions Bumpstead Road,
Haverhill, Suffolk, CB9 7AA, United Kingdom
Tel: +44 (0) 1440 766360 
Fax: +44 (0) 1440 768897

Email: info@dcp-int.co.uk
Email: stephen.bird@dcp-int.com
Email: tom.emery@dcp-int.com